How to distinguish the quality of woven patches?

First of all, check whether the pattern text of the weaving Mark is wrong and whether the size of the pattern text is correct. At the first sight, check whether there is any mistake or omission in the Dao pattern and text of the weaving Mark. Of course, these low-level mistakes can be found at the beginning of the edition. When the bulk goods are handed over to the customers, such low-level mistakes will not appear. Then, next we need to see whether the pattern and text woven by the weaving Mark are fine. As like as two peas or the original, each printed text is quite successful, because it can be successfully achieved from the picture and text. It’s very important to meet the customer’s needs from the graphics and text. If the graphics and text can’t achieve the effect the customer wants, the weaving Mark is unqualified. For the customer, this is a defective product. No one can accept the defective product.

The pattern made not only meets the requirements in shape, but also in size. The weaving Mark itself is very small. Sometimes the size of the pattern needs to be accurate to 0.05mm. If it is slightly larger than 0.05mm, the comparison between the weaving Mark and the original is out of shape. Of course, it is acceptable for some customers to ask for 0.05mm difference in weaving Mark, but for some high-end brands, 0.05mm difference is not enough, so it must be accurate, because this weaving Mark is a long-term word-of-mouth carrier, which carries the brand name, the exquisite and rigorous spirit of the brand, in the brand clothing, this kind of weaving Mark is a tangible word-of-mouth propaganda and no Form brand spirit carrier. So don’t neglect the energy of small weaving marks, delicate and professional.

Secondly, look at the color of weaving marks. The color is generally Pantone color system. In this case, the color comparison is based on the original color or design draft. There is no special explanation for this, but only on sensory judgment.

Third, look at the density of the weaving marks. The density of weaving marks refers to the density of weft. The higher the density, the higher the quality of weaving marks. Weft density refers to the number of yarns in the weaving Mark of 1cm range. If the yarn is thinner, the more fine the weaving marks are. The fine weaving marks are of high brand. Ren’s weaving marks specializes in producing such fine and high-grade weaving marks. Yarn is usually represented by D, 100D is relatively thick, 75D is fine, 50D is finer, 30d is the thinnest yarn.

Fourth, look at the post-processing of weaving marks. After the weaving process, there are generally hot cutting (hot knife cutting), super cutting (ultrasonic cutting), shearing (cutting one by one, then folding 0.7cm from the left and right sides to the inside respectively), folding in half (symmetrical folding), ring mold (that is, ring a square weaving Mark into an irregular pattern shape, such as the weaving chapter, which is to ring a model with a knife or laser gun), and sizing (that is to say It is to put the weaving Mark into the milk white pulp bucket for a while, and then let the weaving Mark dry or air dry. When the pulp on the weaving Mark dries up, the weaving Mark will become stronger. Lock the edge (that is, seal the four sides of the weaving Mark with the thread to prevent it from scattering in the future).

These post-processing procedures determine whether the post-processing link of weaving marks is qualified. The customer requires to choose which post process, and whether it meets the post process processing requirements, such as eager to reach the front of the weaving Mark without cutting hands. Undercutting cannot scatter edges. The cutting and folding should be neat on both sides and should not be skewed. Folding in half requires symmetry, not one long and one short. The ring mold must be cut according to the pattern, not the pattern. Some customers in the sizing process require that after sizing, the weaving Mark should not be too hard, so the sizing personnel should put less slurry and more water to make the slurry thinner. The lock line cannot be locked to the pattern.dav


Post time: Jun-17-2020
WhatsApp Online Chat !